TKLBLS Z4 Professional 4 Channel Mixer 48V Phantom Power 99DSP Bluetooth USB Mixing Console Performance

A. INPUT CHANNEL SECTION

1.BALANCE INPUT (MIC)

Electronically Balanced inputs acceptable a standard XLR male connector. + 48V  Phantom Power available on each input Mic socket.and this switch is on Rear  Phantom Power.  

2.LINE INPUT

The unbalanced Mic input is provided for the use of an unbalance mic and is  designed to accept an unbalanced high impedance input signal.(This use for  connection with instrument like Deck, Turntable,Keyboard attached..)  

3.PAD(-26dB)

When push this switch, attenuates input signal -26dB.If you hear distortion or the  [PEAK] LED @ lights, turn the switch on.  NOTE Turn the [LEVEL] knob to "0" (minimum) before toggling the [PAD] switch on  (==) and off (HL). Otherwise, noise  may be produced.

4.HPF/80HZ

(High-Pass Filter) switches  Turning the switch on will apply a high-pass filter that attenuates frequencies below  80Hz. When speaking into the microphone, you may want to turn this switch on, in  order to reduce unwanted vibration and wind sound received by the microphone.

5.GAIN CONTROL

knobs  Determines the basic volume for each channel, . Adjust these so that the  corresponding [PEAK] LEDs (10) flash briefly when singing or playing the  loudest.Adjusts input sensitivity from -6dB to +38dB,+20dB to +64dB when PAD  switch is on(Pressed)

6.HIEQ  

This control gives you up to 15 dB of boost or cut at 10KHz and above. Use it to add  sizzle to cymbals,and an overall sense of transparency or edge to key -  boards,vocals,guitar,and bacon frying. Turn it down a little to reduce sibilance, or to  hide tape hiss.  

7.MID EQ  

Short for "mid range", this knob provides 15 dB of boost or cut, centered at 2.5KHz.  Mid-range EQ is often thought of as the most dynamic, because the frequencies that  define any particular sound are almost always found in this range. You can create  many interesting and useful EQ changes by turning this knob down as well as up.  

8. LOW EQ  

This control gives you up to 15 dB boost or cut at 80Hz and below.  This frequency represent the punch in bass drums, bass guitar, fat synth  patches,and some really serious male singers.  Note Adjust the sound quality by using the [HIGH] (high frequency band),  [MID](middle frequency band)and [LOW] (low frequency band) knobs. If you do not  need to adjust the sound quality, set the knob to the “middle” (flat) position.  

9.AUX  

Use this contol to set the level of signal from external souce and the main signal control is  recontroled by STEREO or MONO section.  

10.FX/SEND  

Use this control when you want to get effect sound by adjustment of input signal,  when you don't use external source, digital delay will be working which installed  inside.  

11.PAN  

The pan control sends continuosly variable amounts of the post fader signal to either the  left or right busses, In the certer position equal amounts of signal are sent to the left and  right busses.

12.PEAK  

Lights when the volume of input and/or post-equalizer sound is too high. If itis lit, turn  the [GAIN] knob (5) to the left to lower the volume.  

13-14.LEVEL knobs 

For adjusting the volume balance among the channels.  

15.LEFT/RIGHT 5/6  

Connect analog signal devices such as TV or an audio device with RCA output.stereo  input.  

B. MASTER SECTION  

16.AUX SEND CONTROL  

When this button is up, Post signal work as send signal, When this button is down, post  signal work as EFFECT signal.  

17.FX SEND CONTROL  

Adjusts the level of the signal sent to the FX bus.  

18.LED DISPLAY  EFFECT PROGRAM 

When adjust switch 96,97,98,99 more effects are displayed.  

19.EFFECT PROGRAM 

knob  Selects one of the 99 internal effects.  UP TAPE SWITCH One push, one program up, push with more than 5 seconds, hispeed program up.  

DOWN TAPE SWITCH One push, one program down, push with more than 5  seconds, hi- speed program up.  

20.PARAMETER 

Control  Adjusts the parameter(depth,speed,etc.)for the selected effect. The last value used  with each effect type is saved.  

21.EFFECTS LEVEL  

Adjusts the volume of the effect sound.  

22.MP3/BT FADER  

This is a function to adjust the volume of signal connection into each channel and adjust the  volume of output, together with master fader. Normal operating position is at the “O” mark,  providing 4dB of gain above that point, if required.  

23. STEREO LEVEL (OUTPUT MAIN FADER)  

This is a master fader for adjustment for volume of left/right output. Unity gain is the top  their travel.  

24.PHONES (HEADPHONE LEVEL)  

This is a single volume control sends the level to be the PHONES (HEADPHONE  LEVEL)and main monitors.  

25. OUTPUT LEVEL INDICATOR  

This is level meter which shows output levels of left& right channel condition on the way  of operation, therefore, you can see output condition thru this master level indication.  

26. PHANTOM +48V SWITCH/LED  

When this switch is on (.«m ), the LED lights indicating that the unit supplies DC+48V  phantom power to all the XLR plugs of the [MIC/LINE] mono input jacks (1). Turn this  switch on when using a phantom-powered condenser microphone. CAUTION In order  to prevent noise and possible damage to external devices,be sure to leave this switch  off ( BL ) if you do not need phantom power. Turn the [LEVEL] knob of the channels 1-4  to the minimum before operating this switch.  

27. POWER INSTRUCTIONS  

POWER LED is on to indicate that the machine is powered on  

28. USB PLAYER  

USB Playback for WAV/WMA/MP3.

C. MIXER OUTPUT SECTION

29.HEADPHONE 

JACK  Connect a set of headphones. This jack supports a stereo phone plug.  

30. AUX SEND JACK 

This can be used to connect all kinds of aux form outside.  

31.FX SEND JACK  

Unbalance jack comnetors for connect of mon into amplification or for amplification; the  output.  

32.MAIN OUTPUT JACK (LEFT / RIGHT)  

Connect a powered speaker or powered amp. These jacks support both XLR and  phone plugs.  

D. POWER SECTION

33. POWER JACK  

Connect the supplied AC power adapter to this jack.  

34.POWER SWITCH  

Trun the [GAIN],[LEVEL] knobs and [STEREO LEVEL] knob fully to the left(minimum).  Before you turn the power switch on.